ERROR CODE CANON

Error code canon mp145, MP150, MP160 (Download Service Tool V-1050)

Error code canon mp145, MP150, MP160

E2-2 = No paper or paper priter can not rally (can because dirty roll)

E3-3 = Paper hours

E4 = No ink / cartridge

E5-5 = ink cartridges are not installed or installed incorrectly cartirdge (not compatibel)

E8 = absorber full, or Platen waste ink absorber full reset Mita

E9 = connection to digital camera / video camera does not support

E14 = Ink cartridges whose destination are wrong

E15 = color Catridge experiencing run out

E16 - Black Catridge experiencing run out

E17-E19 = problems on the scan head alignment sheet

E22 = Carriage error

E23 = Paper feed error

E24 = Purge unit error (the cleaning head)

E25 = ASF (cam) sensor error

E26 = Internal temperature rise error

E27 = ink absorber full or Platen waste ink absorber full> reset with toolsnya

E28 = Ink cartridge temperature rise error -

E29 = EEPROM error

E33 = Paper feed position error

E35 15 = USB Host VBUD overcurrent error - USB

E37 17 = Abnormal motor driver

E40 20 = Other hardware error

E42 22 = Scanner error

here's how to reset the waste ink counter (E16 error):

1. Turn off the printer (power cable is still tercolok), press and hold the STOP / RESET then press the ON / OFF

2. Hold down the ON / OFF, press the STOP / RESET 2x

3. Release both buttons and the printer will enter SERVICE MODE

4. Printer will be charging

5. Once the printer is done charging, press the STOP / RESET 4x. (Waste ink counter reset)

6. Each time the button STOP / RESET is pressed, the lights ON / OFF will turn green and orange colors

7. Turn off the printer and disconnect the cable POWER

8. Turn the printer back.

The number of the Reset:

pressing button

LED Function Remarks

0 time Green Power off

1 time Orange Service pattern print

2 times Green EEPROM print

3 times Orange EEPROM reset

4 times Green Waste ink counter reset

5) Unplug the power cable. (For MP145 / MP150)

6) Turn Off Power. (For MP160)

CANON MP145 PRINTER INK PROBLEM FULL Absorber (E 2 7 error message)

1. Turn off the printer (press the on / off)

2. press the stop / reset, do not acquitted

3. press again the power button, the power led lights up (not removable).

4. Last stop button / reset, press the stop button again reset 2 times.

5. after the power switch on / off

6. wait until the main LED (led display) show the number 0 on PANEL PRINTER, after pointing the figure 0 immediately press the stop / reset 4 times

7. press the power button 1 time (paper roller rotates, power led blinking)

8.Tunggu up led stop blinking and the printer stand-by (if there is not a direct response to just turn off your printer)

9. turn off your printer.

10. you turn on the printer again.

To reset Canon Printer MP type can also be done by using the Service Tool or MP tool.download hear disini

How to use this September:

1. Turn off the printer (press the on / off)

2. press the stop / reset, do not acquitted

3. press again the power button, the power led lights up (not removable).

4. Last stop button / reset, press the stop button again reset 2 times.

5. after the power switch on / off

6. wait until the main LED (led display) show the number 0 on PANEL PRINTER, after pointing the figure 0, then go to file Service Tool is you download.

7.setelah you extract or open files with WinRAR Service Tool or winzip, open file V1050.exe Service tool will then appear under the picture Sep at.

8.For No4 (region). Choose ASA (for those of us who are in asia pacific)
9. For no.5 select PLAY & PLATTERN
10.Press no.1 if you want to reset the Ink Counter, or
11.Press no.2 if you want to reset the EPROM

* Service MP tool or tools would only work if your printer in conditions of service mode (display O)

For Error 3 trial in check around the pump removal ink gear2 no problem E3 kalaya this cause is whether the stand of loose gear.

Run out to a good Cartride black or color .... enough with pressing the resume around 5secon or to display a reminder on your monitor screen Hila

Resetter Canon MP258

Resetter Canon MP258

Lately canon printers tend to be much cheaper than brand epson printer. So surely the price is very cheap printer canon brand much sought after community. With a price range of 600 thousand printer has three facilities in one (print, scan, copy), compare with epson T13 printer costing 600 thousand cuman can print then. However, also have their own trademark their respective advantages. Whatever brand you definitely need Resetter printer, the following tutorial Resetter Canon MP258.

The features of this printer should reset namely:

If the printer is lit under normal conditions but if there appeared error 5200 print order and the LCD shows P08

Way of handling:

Method 1

Replace the cartridge

Method 2

Wear Resetter tool as below:

Resetter way MP 258 error 5200:

1. Printer is turned off and the power cable attached.

2. Hold down STOP / RESET, then press and hold the POWER button.

3. POWER button is pressed in position, release the button STOP / RESET, then press the STOP / RESET 2 x in the power button is pressed.

4. Last second of this button simultaneously.

5. Wait a few minutes while the printer is the process, then the LCD panel will show zeros.

6. Ignore it if the computer detects the new device.

7. Printer Resetter finished reset tool wear. 3 sheets of paper input before reset the printer.

a.. Download  and run the tool as follows Resetter software

b. Click main, then the printer print one page with the results as follows

 c. Click the EEPROM CLEAR, then click the printer EEPROM like this page print

d. Printer ready ...

CARA RESET CANON PIXMA

Reset Canon Pixma iP1980 way

Printer error on this kind flashing marked with orange LEDs.

Here is a list of error codes (Error Code) from the Canon Pixma iP1980 is marked with orange blink of Led and Led green

3x orange 1x green

Damage / Problems In Mechanics

4x orange 1x green

Get full Absorber overcome by Resetter / general tools

5x orange 1x green

Cartirdge black / color problems. The possibility of damage to the Catridge, Chip is an error or a dirty connector Catridge (rusty or hit the ink)

7x orange 1x green => Same as number 3

Cartirdge black / color problems. The possibility of damage to the Catridge, Chip is an error or a dirty connector Catridge (rusty or hit the ink)

8x orange 1x green

Get full Absorber overcome by Resetter / general tools

12x / 15x orange 1x green

Detksi Catridge.

To overcome such damage at point 2 and 5 above we can use Resetter software

Before doing Resetting printar be in Service Mode by sbb:

- Disconnect / printer power cable Post

- Press and hold the power button with your index finger and then input power cable

- The power button is still on hold, Then your middle finger NG resume button 2 times.

- After the power button

- Printer is not flashing

2. Extract File Resetter_CanoniP1900.rar have downloaded, Then run Generaltool.exe

3. In USB Port select your printer port.

4. Click the Device ID

5. Click the button to Lock Release

6. On the Set Destination Select the type of printer IP1980/1880/1800 (a), Select IP1800 (ASA)

7. Select (check) the EEPROM CLEAR

8. Prepare a blank sheet of paper to print. Then Click the Test Pattern 1

9. Finish your IP1900 Printer normal again.

Download this Tricks

Make sure you use Windows XP